China OEM Oil Water Separation Machine Supplier – JXH type micro heat regenerative dryer – Juxian
China OEM Oil Water Separation Machine Supplier – JXH type micro heat regenerative dryer – Juxian Detail:
Product introduction
Micro thermal adsorption compressed air dryer is a kind of adsorption dryer developed by absorbing the advantages of thermal adsorption and non thermal adsorption compressed air dryer.It avoids the disadvantages of short switching time and large loss of regenerative air of the non-thermal adsorption compressed air dryer, and also overcomes the disadvantages of large power consumption of the thermal adsorption compressed air dryer.It is the most economical and energy-saving adsorption dryer in the purification industry, and is widely used in electronics, food, metallurgy, electric power, chemical industry, petroleum, medicine, light textile, tobacco, instruments, meters, automatic control and other industries.
Working principle
This series of micro thermal adsorption compressed air dryer is a kind of equipment which uses micro heating regeneration method to dry compressed air according to the principle of pressure swing adsorption.Under a certain pressure, the compressed air flows through the adsorbent (dry) bed from bottom to top, under low temperature and high pressure, the water vapor in the compressed air will transfer to the adsorbent surface, that is, the adsorbent absorbs the water in the air to tend to balance, so that the compressed air is dry, this is the adsorption (work) process.
When the pressure drop of dry air (regenerated air), the gas expansion after heating, and then contact with the adsorbent saturated water, water in the adsorbent to regenerated air, until the balance, so that the adsorbent get dry, this is desorption (regeneration) process.That is, at low temperature and high pressure, the water is absorbed (work), and at high temperature and low pressure, the water is desorbed (regeneration).
The dryer is a double cylinder structure, the cylinder is filled with adsorbent (dryer), when one adsorption cylinder in the drying process, the other adsorption cylinder in the desorption process.
Technical characteristics
1. heating control adopts non-contact solid state switch, automatic constant temperature control, long life;With a variety of fault alarm functions.
2. advanced variable program, stable and reliable operation.
3. the use of microcomputer control, digital display of two towers alternately running state.
4. the use of safe and reliable control components, to ensure that the controller output signal safe and accurate to reach the instruction target.
5. to ensure the stable and reliable dew point of finished products, low energy consumption.
6. simple and generous structure, humanized design, easy to operate and maintain.
7. in the case of failure of the heat part can be automatically switched to no heat operation mode.
8. equipped with RS485/RS232 intermodal interface, can carry out remote communication, centralized monitoring and air compressor joint control.
Technical indicators
| Working pressure | 0.6-1.0mpa (1.0-1.3mpa upon request) |
| Inlet temperature | < 50℃ |
| Dew point of finished product | ≤-40℃(alumina)≤-52℃(molecular sieve) |
| Regeneration gas consumption | ≤6% |
| Pressure loss | ≤ 0.02mpa |
| Operation period | 10 minutes |
Technical parameters
|
Model |
Rated capacity (after Nm/h) |
Nominal inlet diameter DN (mm) |
Power supply (V /Hz) |
Installed power (kW) |
Floor area size (mm) |
|
JXH-1 |
1.2 |
25 |
220/50 |
0.5 |
840 * 320 * 1370 |
|
JXH-2 |
2.4 |
25 |
220/50 |
1.0 |
880 * 320 * 11450 |
|
JXH-3 |
3.6 |
32 |
220/50 |
1.5 |
980 * 350 * 11540 |
|
JXH-6 |
6.8 |
40 |
220/50 |
2.2 |
1100 * 420 * 1820 |
|
JXH-10 |
10.9 |
50 |
380/50 |
5.0 |
1250 * 500 * 2150 |
|
JXH-16 |
16.5 |
65 |
380/50 |
7.5 |
1420 * 550 * 2500 |
|
JXH-20 |
22 |
65 |
380/50 |
9.0 |
1560 * 650 * 2500 |
|
JXH-30 |
32 |
80 |
380/50 |
15.0 |
1750 * 700 * 2530 |
|
JXH-40 |
43.5 |
100 |
380/50 |
18.0 |
1840 * 900 * 2550 |
|
JXH-50 |
53 |
100 |
380/50 |
23.0 |
1920 * 900 * 2680 |
|
JXH-60 |
65 |
125 |
380/50 |
30.0 |
2100 * 1000 * 2870 |
|
JXH-80 |
85 |
150 |
380/50 |
35.0 |
2520 * 1200 * 2820 |
|
JXH-100 |
108 |
150 |
380/50 |
45.0 |
2600 * 1200 * 2950 |
|
JXH-150 |
160 |
200 |
380/50 |
70.0 |
3000 * 1400 * 3170 |
|
JXH-200 |
210 |
200 |
380/50 |
90.0 |
3700 * 2000 * 3300 |
Product detail pictures:
Related Product Guide:
"Quality 1st, Honesty as base, Sincere company and mutual profit" is our idea, in an effort to create consistently and pursue the excellence for China OEM Oil Water Separation Machine Supplier – JXH type micro heat regenerative dryer – Juxian , The product will supply to all over the world, such as: Costa rica, Vancouver, Jordan, We have gained a lot of recognition among customers spread all across the world. They trust us and always give repetitive orders. Furthermore, mentioned below are some of the major factors that have played significant role in our tremendous growth in this domain.
By Frederica from Suriname - 2017.12.02 14:11
This is the first business after our company establish, products and services are very satisfying, we have a good start, we hope to cooperate continuous in the future!
By Joseph from Namibia - 2017.09.09 10:18
