China OEM Dehydrator Manufacturers – JXH type micro heat regenerative dryer – Juxian
China OEM Dehydrator Manufacturers – JXH type micro heat regenerative dryer – Juxian Detail:
Product introduction
Micro thermal adsorption compressed air dryer is a kind of adsorption dryer developed by absorbing the advantages of thermal adsorption and non thermal adsorption compressed air dryer.It avoids the disadvantages of short switching time and large loss of regenerative air of the non-thermal adsorption compressed air dryer, and also overcomes the disadvantages of large power consumption of the thermal adsorption compressed air dryer.It is the most economical and energy-saving adsorption dryer in the purification industry, and is widely used in electronics, food, metallurgy, electric power, chemical industry, petroleum, medicine, light textile, tobacco, instruments, meters, automatic control and other industries.
Working principle
This series of micro thermal adsorption compressed air dryer is a kind of equipment which uses micro heating regeneration method to dry compressed air according to the principle of pressure swing adsorption.Under a certain pressure, the compressed air flows through the adsorbent (dry) bed from bottom to top, under low temperature and high pressure, the water vapor in the compressed air will transfer to the adsorbent surface, that is, the adsorbent absorbs the water in the air to tend to balance, so that the compressed air is dry, this is the adsorption (work) process.
When the pressure drop of dry air (regenerated air), the gas expansion after heating, and then contact with the adsorbent saturated water, water in the adsorbent to regenerated air, until the balance, so that the adsorbent get dry, this is desorption (regeneration) process.That is, at low temperature and high pressure, the water is absorbed (work), and at high temperature and low pressure, the water is desorbed (regeneration).
The dryer is a double cylinder structure, the cylinder is filled with adsorbent (dryer), when one adsorption cylinder in the drying process, the other adsorption cylinder in the desorption process.
Technical characteristics
1. heating control adopts non-contact solid state switch, automatic constant temperature control, long life;With a variety of fault alarm functions.
2. advanced variable program, stable and reliable operation.
3. the use of microcomputer control, digital display of two towers alternately running state.
4. the use of safe and reliable control components, to ensure that the controller output signal safe and accurate to reach the instruction target.
5. to ensure the stable and reliable dew point of finished products, low energy consumption.
6. simple and generous structure, humanized design, easy to operate and maintain.
7. in the case of failure of the heat part can be automatically switched to no heat operation mode.
8. equipped with RS485/RS232 intermodal interface, can carry out remote communication, centralized monitoring and air compressor joint control.
Technical indicators
| Working pressure | 0.6-1.0mpa (1.0-1.3mpa upon request) |
| Inlet temperature | < 50℃ |
| Dew point of finished product | ≤-40℃(alumina)≤-52℃(molecular sieve) |
| Regeneration gas consumption | ≤6% |
| Pressure loss | ≤ 0.02mpa |
| Operation period | 10 minutes |
Technical parameters
|
Model |
Rated capacity (after Nm/h) |
Nominal inlet diameter DN (mm) |
Power supply (V /Hz) |
Installed power (kW) |
Floor area size (mm) |
|
JXH-1 |
1.2 |
25 |
220/50 |
0.5 |
840 * 320 * 1370 |
|
JXH-2 |
2.4 |
25 |
220/50 |
1.0 |
880 * 320 * 11450 |
|
JXH-3 |
3.6 |
32 |
220/50 |
1.5 |
980 * 350 * 11540 |
|
JXH-6 |
6.8 |
40 |
220/50 |
2.2 |
1100 * 420 * 1820 |
|
JXH-10 |
10.9 |
50 |
380/50 |
5.0 |
1250 * 500 * 2150 |
|
JXH-16 |
16.5 |
65 |
380/50 |
7.5 |
1420 * 550 * 2500 |
|
JXH-20 |
22 |
65 |
380/50 |
9.0 |
1560 * 650 * 2500 |
|
JXH-30 |
32 |
80 |
380/50 |
15.0 |
1750 * 700 * 2530 |
|
JXH-40 |
43.5 |
100 |
380/50 |
18.0 |
1840 * 900 * 2550 |
|
JXH-50 |
53 |
100 |
380/50 |
23.0 |
1920 * 900 * 2680 |
|
JXH-60 |
65 |
125 |
380/50 |
30.0 |
2100 * 1000 * 2870 |
|
JXH-80 |
85 |
150 |
380/50 |
35.0 |
2520 * 1200 * 2820 |
|
JXH-100 |
108 |
150 |
380/50 |
45.0 |
2600 * 1200 * 2950 |
|
JXH-150 |
160 |
200 |
380/50 |
70.0 |
3000 * 1400 * 3170 |
|
JXH-200 |
210 |
200 |
380/50 |
90.0 |
3700 * 2000 * 3300 |
Product detail pictures:
Related Product Guide:
We insist on offering high-quality creation with superior business enterprise concept, honest revenue plus the greatest and fast service. it will bring you not only the high quality solution and huge profit, but essentially the most significant is usually to occupy the endless market for China OEM Dehydrator Manufacturers – JXH type micro heat regenerative dryer – Juxian , The product will supply to all over the world, such as: Madagascar, Singapore, Ukraine, We will not only continuously introduce technical guidance of experts from both home and abroad, but also develop the new and advanced products constantly to satisfactorily meet the needs of our clients all over the world.
By Nina from Bahrain - 2018.11.06 10:04
We have been cooperated with this company for many years, the company always ensure timely delivery ,good quality and correct number, we are good partners.
By Jason from America - 2017.11.20 15:58
