China OEM Dehydrator Manufacturers – JXH type micro heat regenerative dryer – Juxian

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

We are going to make every single effort for being excellent and excellent, and accelerate our ways for standing while in the rank of international top-grade and high-tech enterprises for Portable O2 Generator, HEPA Filters, Air Filter Mesh, Should you be interested in almost any goods, remember to truly feel totally free to get in touch with us for further facts or be sure to deliver us email right, we will reply you in just 24 hrs as well as the finest quotation are going to be provided.
China OEM Dehydrator Manufacturers – JXH type micro heat regenerative dryer – Juxian Detail:

Product introduction

Micro thermal adsorption compressed air dryer is a kind of adsorption dryer developed by absorbing the advantages of thermal adsorption and non thermal adsorption compressed air dryer.It avoids the disadvantages of short switching time and large loss of regenerative air of the non-thermal adsorption compressed air dryer, and also overcomes the disadvantages of large power consumption of the thermal adsorption compressed air dryer.It is the most economical and energy-saving adsorption dryer in the purification industry, and is widely used in electronics, food, metallurgy, electric power, chemical industry, petroleum, medicine, light textile, tobacco, instruments, meters, automatic control and other industries.

Working principle

This series of micro thermal adsorption compressed air dryer is a kind of equipment which uses micro heating regeneration method to dry compressed air according to the principle of pressure swing adsorption.Under a certain pressure, the compressed air flows through the adsorbent (dry) bed from bottom to top, under low temperature and high pressure, the water vapor in the compressed air will transfer to the adsorbent surface, that is, the adsorbent absorbs the water in the air to tend to balance, so that the compressed air is dry, this is the adsorption (work) process.

When the pressure drop of dry air (regenerated air), the gas expansion after heating, and then contact with the adsorbent saturated water, water in the adsorbent to regenerated air, until the balance, so that the adsorbent get dry, this is desorption (regeneration) process.That is, at low temperature and high pressure, the water is absorbed (work), and at high temperature and low pressure, the water is desorbed (regeneration).

The dryer is a double cylinder structure, the cylinder is filled with adsorbent (dryer), when one adsorption cylinder in the drying process, the other adsorption cylinder in the desorption process.

Technical characteristics

1. heating control adopts non-contact solid state switch, automatic constant temperature control, long life;With a variety of fault alarm functions.

2. advanced variable program, stable and reliable operation.

3. the use of microcomputer control, digital display of two towers alternately running state.

4. the use of safe and reliable control components, to ensure that the controller output signal safe and accurate to reach the instruction target.

5. to ensure the stable and reliable dew point of finished products, low energy consumption.

6. simple and generous structure, humanized design, easy to operate and maintain.

7. in the case of failure of the heat part can be automatically switched to no heat operation mode.

8. equipped with RS485/RS232 intermodal interface, can carry out remote communication, centralized monitoring and air compressor joint control.

Technical indicators

Working pressure 0.6-1.0mpa (1.0-1.3mpa upon request)
Inlet temperature < 50℃
Dew point of finished product ≤-40℃(alumina)≤-52℃(molecular sieve)
Regeneration gas consumption ≤6%
Pressure loss ≤ 0.02mpa
Operation period 10 minutes

Technical parameters

Model

Rated capacity

(after Nm/h)

Nominal inlet diameter DN (mm)

Power supply (V /Hz)

Installed power (kW)

Floor area size (mm)

JXH-1

1.2

25

220/50

0.5

840 * 320 * 1370

JXH-2

2.4

25

220/50

1.0

880 * 320 * 11450

JXH-3

3.6

32

220/50

1.5

980 * 350 * 11540

JXH-6

6.8

40

220/50

2.2

1100 * 420 * 1820

JXH-10

10.9

50

380/50

5.0

1250 * 500 * 2150

JXH-16

16.5

65

380/50

7.5

1420 * 550 * 2500

JXH-20

22

65

380/50

9.0

1560 * 650 * 2500

JXH-30

32

80

380/50

15.0

1750 * 700 * 2530

JXH-40

43.5

100

380/50

18.0

1840 * 900 * 2550

JXH-50

53

100

380/50

23.0

1920 * 900 * 2680

JXH-60

65

125

380/50

30.0

2100 * 1000 * 2870

JXH-80

85

150

380/50

35.0

2520 * 1200 * 2820

JXH-100

108

150

380/50

45.0

2600 * 1200 * 2950

JXH-150

160

200

380/50

70.0

3000 * 1400 * 3170

JXH-200

210

200

380/50

90.0

3700 * 2000 * 3300


Product detail pictures:

China OEM Dehydrator Manufacturers –  JXH type micro heat regenerative dryer –  Juxian detail pictures


Related Product Guide:

Often customer-oriented, and it's our ultimate target to become not only probably the most reputable, trustable and honest provider, but also the partner for our customers for China OEM Dehydrator Manufacturers – JXH type micro heat regenerative dryer – Juxian , The product will supply to all over the world, such as: Belgium, Seattle, Italy, Business philosophy: Take the customer as the Center, take the quality as the life, integrity, responsibility, focus, innovation.We will provide professional, quality in return for the trust of customers, with most major global suppliers,all of our employees will work together and move forward together.
  • This supplier offers high quality but low price products, it is really a nice manufacturer and business partner.
    5 Stars By Alice from Oman - 2018.06.28 19:27
    This is a honest and trustworthy company, technology and equipment are very advanced and the prodduct is very adequate, there is no worry in the suppliment.
    5 Stars By Victoria from Morocco - 2017.11.20 15:58
    Write your message here and send it to us