China OEM Air Compressor Post-Processing Equipment Pricelist – JXH type micro heat regenerative dryer – Juxian

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

We thinks what clients think, the urgency of urgency to act from the interests of a purchaser position of principle, allowing for greater top quality, decrease processing costs, price ranges are much more reasonable, won the new and aged prospects the support and affirmation for Flange Type Check Valve, 5nm3/H 99.9% Psa Nitrogen Generator, Filter Cartridge, We've been prepared to cooperate with company friends from at your home and overseas and produce a wonderful future with each other.
China OEM Air Compressor Post-Processing Equipment Pricelist – JXH type micro heat regenerative dryer – Juxian Detail:

Product introduction

Micro thermal adsorption compressed air dryer is a kind of adsorption dryer developed by absorbing the advantages of thermal adsorption and non thermal adsorption compressed air dryer.It avoids the disadvantages of short switching time and large loss of regenerative air of the non-thermal adsorption compressed air dryer, and also overcomes the disadvantages of large power consumption of the thermal adsorption compressed air dryer.It is the most economical and energy-saving adsorption dryer in the purification industry, and is widely used in electronics, food, metallurgy, electric power, chemical industry, petroleum, medicine, light textile, tobacco, instruments, meters, automatic control and other industries.

Working principle

This series of micro thermal adsorption compressed air dryer is a kind of equipment which uses micro heating regeneration method to dry compressed air according to the principle of pressure swing adsorption.Under a certain pressure, the compressed air flows through the adsorbent (dry) bed from bottom to top, under low temperature and high pressure, the water vapor in the compressed air will transfer to the adsorbent surface, that is, the adsorbent absorbs the water in the air to tend to balance, so that the compressed air is dry, this is the adsorption (work) process.

When the pressure drop of dry air (regenerated air), the gas expansion after heating, and then contact with the adsorbent saturated water, water in the adsorbent to regenerated air, until the balance, so that the adsorbent get dry, this is desorption (regeneration) process.That is, at low temperature and high pressure, the water is absorbed (work), and at high temperature and low pressure, the water is desorbed (regeneration).

The dryer is a double cylinder structure, the cylinder is filled with adsorbent (dryer), when one adsorption cylinder in the drying process, the other adsorption cylinder in the desorption process.

Technical characteristics

1. heating control adopts non-contact solid state switch, automatic constant temperature control, long life;With a variety of fault alarm functions.

2. advanced variable program, stable and reliable operation.

3. the use of microcomputer control, digital display of two towers alternately running state.

4. the use of safe and reliable control components, to ensure that the controller output signal safe and accurate to reach the instruction target.

5. to ensure the stable and reliable dew point of finished products, low energy consumption.

6. simple and generous structure, humanized design, easy to operate and maintain.

7. in the case of failure of the heat part can be automatically switched to no heat operation mode.

8. equipped with RS485/RS232 intermodal interface, can carry out remote communication, centralized monitoring and air compressor joint control.

Technical indicators

Working pressure 0.6-1.0mpa (1.0-1.3mpa upon request)
Inlet temperature < 50℃
Dew point of finished product ≤-40℃(alumina)≤-52℃(molecular sieve)
Regeneration gas consumption ≤6%
Pressure loss ≤ 0.02mpa
Operation period 10 minutes

Technical parameters

Model

Rated capacity

(after Nm/h)

Nominal inlet diameter DN (mm)

Power supply (V /Hz)

Installed power (kW)

Floor area size (mm)

JXH-1

1.2

25

220/50

0.5

840 * 320 * 1370

JXH-2

2.4

25

220/50

1.0

880 * 320 * 11450

JXH-3

3.6

32

220/50

1.5

980 * 350 * 11540

JXH-6

6.8

40

220/50

2.2

1100 * 420 * 1820

JXH-10

10.9

50

380/50

5.0

1250 * 500 * 2150

JXH-16

16.5

65

380/50

7.5

1420 * 550 * 2500

JXH-20

22

65

380/50

9.0

1560 * 650 * 2500

JXH-30

32

80

380/50

15.0

1750 * 700 * 2530

JXH-40

43.5

100

380/50

18.0

1840 * 900 * 2550

JXH-50

53

100

380/50

23.0

1920 * 900 * 2680

JXH-60

65

125

380/50

30.0

2100 * 1000 * 2870

JXH-80

85

150

380/50

35.0

2520 * 1200 * 2820

JXH-100

108

150

380/50

45.0

2600 * 1200 * 2950

JXH-150

160

200

380/50

70.0

3000 * 1400 * 3170

JXH-200

210

200

380/50

90.0

3700 * 2000 * 3300


Product detail pictures:

China OEM Air Compressor Post-Processing Equipment Pricelist –  JXH type micro heat regenerative dryer –  Juxian detail pictures


Related Product Guide:

We are commitment to offer the competitive price ,outstanding products quality, as well as fast delivery for China OEM Air Compressor Post-Processing Equipment Pricelist – JXH type micro heat regenerative dryer – Juxian , The product will supply to all over the world, such as: Barbados, Morocco, Russia, Based on our guiding principle of quality is the key to development, we continually strive to exceed our customers' expectations. As such, we sincerely invite all interested companies to contact us for future cooperation, We welcome old and new customers to hold hands together for exploring and developing; For more information, please feel free to contact us. Thanks. Advanced equipment, strict quality control, customer-orientation service, initiative summary and improvement of defects and extensive industry experience enable us to guarantee more customer satisfaction and reputation which, in return, brings us more orders and benefits. If you are interested in any of our products, please feel free to contact us. Inquiry or visit to our company are warmly welcome. We sincerely hope to start a win-win and friendly partnership with you. You can see more details in our website.
  • The supplier cooperation attitude is very good, encountered various problems, always willing to cooperate with us, to us as the real God.
    5 Stars By Maxine from Paraguay - 2018.11.28 16:25
    The supplier abide the theory of "quality the basic, trust the first and management the advanced" so that they can ensure a reliable product quality and stable customers.
    5 Stars By Pag from Turkey - 2017.07.28 15:46
    Write your message here and send it to us