China OEM Air Compressor Parts Pricelist – JXH type micro heat regenerative dryer – Juxian

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

We also supply merchandise sourcing and flight consolidation companies. We now have our very own manufacturing facility and sourcing business. We could present you with almost every kind of product relevant to our solution array for DPF Filter, Oxgen Generator, China Air Filter, Welcome your enquiry, greatest service is going to be provided with full heart.
China OEM Air Compressor Parts Pricelist – JXH type micro heat regenerative dryer – Juxian Detail:

Product introduction

Micro thermal adsorption compressed air dryer is a kind of adsorption dryer developed by absorbing the advantages of thermal adsorption and non thermal adsorption compressed air dryer.It avoids the disadvantages of short switching time and large loss of regenerative air of the non-thermal adsorption compressed air dryer, and also overcomes the disadvantages of large power consumption of the thermal adsorption compressed air dryer.It is the most economical and energy-saving adsorption dryer in the purification industry, and is widely used in electronics, food, metallurgy, electric power, chemical industry, petroleum, medicine, light textile, tobacco, instruments, meters, automatic control and other industries.

Working principle

This series of micro thermal adsorption compressed air dryer is a kind of equipment which uses micro heating regeneration method to dry compressed air according to the principle of pressure swing adsorption.Under a certain pressure, the compressed air flows through the adsorbent (dry) bed from bottom to top, under low temperature and high pressure, the water vapor in the compressed air will transfer to the adsorbent surface, that is, the adsorbent absorbs the water in the air to tend to balance, so that the compressed air is dry, this is the adsorption (work) process.

When the pressure drop of dry air (regenerated air), the gas expansion after heating, and then contact with the adsorbent saturated water, water in the adsorbent to regenerated air, until the balance, so that the adsorbent get dry, this is desorption (regeneration) process.That is, at low temperature and high pressure, the water is absorbed (work), and at high temperature and low pressure, the water is desorbed (regeneration).

The dryer is a double cylinder structure, the cylinder is filled with adsorbent (dryer), when one adsorption cylinder in the drying process, the other adsorption cylinder in the desorption process.

Technical characteristics

1. heating control adopts non-contact solid state switch, automatic constant temperature control, long life;With a variety of fault alarm functions.

2. advanced variable program, stable and reliable operation.

3. the use of microcomputer control, digital display of two towers alternately running state.

4. the use of safe and reliable control components, to ensure that the controller output signal safe and accurate to reach the instruction target.

5. to ensure the stable and reliable dew point of finished products, low energy consumption.

6. simple and generous structure, humanized design, easy to operate and maintain.

7. in the case of failure of the heat part can be automatically switched to no heat operation mode.

8. equipped with RS485/RS232 intermodal interface, can carry out remote communication, centralized monitoring and air compressor joint control.

Technical indicators

Working pressure 0.6-1.0mpa (1.0-1.3mpa upon request)
Inlet temperature < 50℃
Dew point of finished product ≤-40℃(alumina)≤-52℃(molecular sieve)
Regeneration gas consumption ≤6%
Pressure loss ≤ 0.02mpa
Operation period 10 minutes

Technical parameters

Model

Rated capacity

(after Nm/h)

Nominal inlet diameter DN (mm)

Power supply (V /Hz)

Installed power (kW)

Floor area size (mm)

JXH-1

1.2

25

220/50

0.5

840 * 320 * 1370

JXH-2

2.4

25

220/50

1.0

880 * 320 * 11450

JXH-3

3.6

32

220/50

1.5

980 * 350 * 11540

JXH-6

6.8

40

220/50

2.2

1100 * 420 * 1820

JXH-10

10.9

50

380/50

5.0

1250 * 500 * 2150

JXH-16

16.5

65

380/50

7.5

1420 * 550 * 2500

JXH-20

22

65

380/50

9.0

1560 * 650 * 2500

JXH-30

32

80

380/50

15.0

1750 * 700 * 2530

JXH-40

43.5

100

380/50

18.0

1840 * 900 * 2550

JXH-50

53

100

380/50

23.0

1920 * 900 * 2680

JXH-60

65

125

380/50

30.0

2100 * 1000 * 2870

JXH-80

85

150

380/50

35.0

2520 * 1200 * 2820

JXH-100

108

150

380/50

45.0

2600 * 1200 * 2950

JXH-150

160

200

380/50

70.0

3000 * 1400 * 3170

JXH-200

210

200

380/50

90.0

3700 * 2000 * 3300


Product detail pictures:

China OEM Air Compressor Parts Pricelist –  JXH type micro heat regenerative dryer –  Juxian detail pictures


Related Product Guide:

"Control the standard by the details, show the toughness by quality". Our firm has strived to establish a highly efficient and stable workers workforce and explored an effective high-quality management system for China OEM Air Compressor Parts Pricelist – JXH type micro heat regenerative dryer – Juxian , The product will supply to all over the world, such as: Chicago, Kuwait, Cape Town, Our company has already had a lot of top factories and qualified technology teams in China, offering the best goods, techniques and services to worldwide customers. Honesty is our principle, skilled operation is our work, service is our goal, and customers' satisfaction is our future!
  • We are really happy to find such a manufacturer that ensuring product quality at the same time the price is very cheap.
    5 Stars By Marguerite from Wellington - 2018.11.06 10:04
    The sales manager is very patient, we communicated about three days before we decided to cooperate, finally, we are very satisfied with this cooperation!
    5 Stars By Odelette from Tanzania - 2017.09.29 11:19
    Write your message here and send it to us